How To Take Apart A Floureon Camera

Dec 22, 2014.

Start and foremost, nosotros'd like to country that whatsoever and all of what we're about to discuss can exist harmful to your camera if done improperly. Having said that, you lot should non endeavour any of the post-obit repairs unless y'all are confident in your power to properly exercise and so. Also, It should become without saying that your photographic camera should be asunder from power earlier attempting whatsoever of this. Please experience free to leave any comments and/or questions in the comments section.

Nosotros do not sell Infrared LED boards or other parts. This guide is for informational purposes just.

Replacing the Infrared LED Board

Replacing an Infrared (IR) LED board is not terribly complicated. Often times, it will exist the easiest to access of all internal components of the whole camera. After determining and then removing the portion of the camera torso that needs to come up off in order to access the IR board, you'll need to detach the IR board from the rest of the housing. This is washed easily by removing the screws that secure the IR board to the camera body and the remaining "guts" inside the camera. You lot can expect find betwixt two and vii retaining screws. Afterwards this, you lot'll notice that you're able to pull the board abroad from the remaining components, only the black/red colored power cable will nonetheless be attached to a white colored socket on the dorsum of the IR lath. While pulling from the base of operations of the connector, remove the power cable from the IR board. At this time y'all're gratuitous to dispose of the damaged board and drop in the new one in reverse order.

Replacing the Lens inside a security photographic camera

From here on out, don't be surprised if yous find yourself needing to nearly completely detach the photographic camera in order to gain access to the components you need. Your lens, whether it's a fixed or adjustable blazon lens, is no exception to this. Your IR lath will likely get your first hurdle; in almost all cases it will need to removed entirely. In the case of fixed lenses, this volition probably exist the merely thing in your style. From hither, you'll likely be able to loosen a single set spiral and the lens will thread right off it'south mountain.

The manually adaptable lenses tin can exist significantly more complicated if this is your get-go rodeo. In certain cases, manually adaptable lenses accept gear "sleeves" that tighten down around the zoom and focus portion of the lens. They work alongside another ready of gears that are continued to your cameras external aligning knobs. When replacing a lens with this blazon of configuration, those sleeves will need to be removed and placed on your new lens. Proper gear alignment is crucial as your camera will no longer be able to be adjusted until you lot get this step correct. Manually adaptable lenses that contain no external adjustment knobs, and are instead adapted by turning the lens itself with the use of small set screws, tin be removed just as easily and in the same style as a fixed lens.

*Your lens may accept a cream ring seated effectually information technology. Equally unlikely as it may seem, this ring is crucial to photographic camera performance. Be sure to put this foam ring dorsum into its proper place.

Replacing the CCD or CMOS Image Sensor

An image sensor is piece of cake plenty to locate in a security camera. Information technology will be directly attached to your lens and volition also always contain a square, or rectangular, piece of glass directly in the center of the board. It should go without maxim then that your lens will obviously need to be removed; this volition well-nigh ordinarily mean removing your IR lath again besides. In one case the other components accept been removed, you'll either demand to detach your image sensor from the body of the camera, and/or from the photographic camera's power lath if it contains 1. Any cables will also need to be detached from the paradigm sensor at this time.

*While installing your new image sensor, be extremely careful not to jar or smudge the glass piece located in the center of the board.

Power Board

Replacing your power lath can be very hit or miss. It's usually positioned in a sort of "caboose" way at the back of the photographic camera. When this is like shooting fish in a barrel, you're able to pull out all of the internal pieces of the camera at one time later disconnecting them from the cables coming from the pigtail. This will expose the power board at the rear of the associates making it very like shooting fish in a barrel to disconnect and swap with your replacement. Things can easily go the other way; it'due south not uncommon for internal components not to be connected together or not in this way. These scenarios will hateful removing every component betwixt you lot and the power board. This can quickly turn into a game of Legos without an instruction booklet. For that reason, we'd recommend taking a video or pictures of your disassembly process to make reassembly easier. As well, be certain to take note of which cables are connected to where on these boards and how they're configured on the pins.

Don Stephens is a Technical Back up Manager at CCTV Camera World, a leading Security Photographic camera benefactor located in Buffalo, NY. His expanse of expertise is in designing professional security camera systems for medium and large scale businesses, schools, and government projects.

Connect with the author via: Twitter  |   Facebook  |   Youtube

Source: https://www.cctvcameraworld.com/cctv-cameras-repair/

Posted by: beckpasm1937.blogspot.com

Share this post